What it means
E31 means the dryer's contact sensor reads a frequency that is too high, per Electrolux's dryer chart. Empty the drum and look for anything lodged against the sensor. If E31 returns with a clear drum, book a technician.
Electrolux dryer E31 / Sensors
E31 means the dryer's contact sensor reads a frequency that is too high, per Electrolux's dryer chart. Empty the drum and look for anything lodged against the sensor. If E31 returns with a clear drum, book a technician.
Also shown as E31
E31 means the dryer's contact sensor reads a frequency that is too high, per Electrolux's dryer chart. Empty the drum and look for anything lodged against the sensor. If E31 returns with a clear drum, book a technician.
Switch the dryer off at the plug, take out the laundry and look at the metal sensor strips inside the drum.
E31 returns with a clear drum and clean sensor strips.
Your checklist, kept on this device

Switch the dryer off at the plug, take out the laundry and look at the metal sensor strips inside the drum. The chart lists a foreign object interfering with the sensor as a cause.

Residue from fabric softener sheets can coat the sensing bars. Wipe them with a cloth dampened with rubbing alcohol, as Electrolux's long-drying article suggests for moisture bars.

Check the drum, door seal and lint area for small metal objects that can bridge or touch the sensor.

Use any button but Cancel to wake it up, then hold Cancel and Start/Pause together for a six-second count. The last error shows; E00 means none.

If E31 comes back with a clear drum, the chart's next step is to test the sensor and wiring and then the control board.
Send us the model and the checks you have done, and open your request here.
Book a visit


A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The contact sensor reads how damp the load is.
Read the definitionThe frequency the control reads from the contact sensor is too high. The chart gives two possible conditions: a defective electronic control board or a foreign object interfering with the sensor.
Read the supporting manualThe contact sensor and its wiring. If no problem is found with the sensor, the chart replaces the electronic control board.
Read the supporting manualE32 is the same sensor reading too low. Both rows have the same conditions and the same solution, so the visit is identical.
Read the supporting manualThe contact sensor tells the dryer when clothes are wet. A reading outside its range can end cycles early or run them long.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
P/N 137265000B (1202); Canadian SKU EIMED6CJIW; original file dated 2009 / sheet p.1 (Error Code Chart)
Manufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Row E31 of the Ceres-platform dryer chart. The cleaning step comes from Electrolux's long-drying article.
The chart does not say so. Electrolux does warn that softener residue can coat the moisture sensor bars, so wiping them is a safe first step. [2]
No. E 4 appears in the Owner Center guide as a failed humidity sensor, while E31 is a frequency reading on the technician chart.
It may stop or end cycles. A dryer that finishes a normal load with no code is not showing it.
The model number, whether E32 has also appeared and what you found in the drum.
Codes, symptoms, parts and service
E32 means the dryer's contact sensor reads a frequency that is too low, per Electrolux's dryer chart. Look for anything lodged against the sensor and wipe the strips; if E32 returns, book a technician.
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
The contact sensor reads how damp the load is. Electrolux’s dryer sheet labels its test row “MOIST. BARS” and ties E31 and E32 to a frequency reading that is too high or too low. A foreign object touching the sensor is one listed cause.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.