What it means
E32 means the dryer's contact sensor reads a frequency that is too low, per Electrolux's dryer chart. Look for anything lodged against the sensor and wipe the strips; if E32 returns, book a technician.
Electrolux dryer E32 / Sensors
E32 means the dryer's contact sensor reads a frequency that is too low, per Electrolux's dryer chart. Look for anything lodged against the sensor and wipe the strips; if E32 returns, book a technician.
Also shown as E32
E32 means the dryer's contact sensor reads a frequency that is too low, per Electrolux's dryer chart. Look for anything lodged against the sensor and wipe the strips; if E32 returns, book a technician.
Unplug the dryer and remove the load.
E32 returns after the strips are clean.
Your checklist, kept on this device

Unplug the dryer and remove the load. A foreign object touching the sensor is the first condition on the chart.

Wipe the metal strips with a cloth and a little rubbing alcohol. Electrolux says softener-sheet residue can stop them from sensing wet clothes.

Wet lint packed near the sensor can change its reading. Clear the lint screen and the opening.

Tap any button other than Cancel to wake the dryer, then keep Cancel and Start/Pause pressed together for six seconds.

The chart checks the sensor and wiring and then replaces the control board if they are fine.
Send us the model and the checks you have done, and open your request here.
Book a visit


A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The contact sensor reads how damp the load is.
Read the definitionThe contact sensor's frequency is below its range. The chart names a defective control board or a foreign object interfering with the sensor.
Read the supporting manualBoth are the sensor reading outside its range, one high and one low. Both are solved by checking the sensor and wiring and then the board.
Read the supporting manualClean the strips and remove objects. If neither changes anything, a meter and a replacement board are the sheet's remaining steps.
Read the supporting manualIf it completes loads without the code, yes. If it stops, choose a timed cycle and book.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
P/N 137265000B (1202); Canadian SKU EIMED6CJIW; original file dated 2009 / sheet p.1 (Error Code Chart)
Manufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Row E32 of the dryer chart, the low-frequency twin of E31.
The chart lists it first, as the board being defective, but only replaces it after the sensor and wiring pass. [1]
No. It means the sensor's electrical reading is out of range, which is different from the wetness of the load.
It does not signal a heat or fire problem, but the dryer may mis-time cycles, so get it checked.
For E32, the model number and what you found on the sensor strips and in the drum, plus whether E31 has also appeared.
Codes, symptoms, parts and service
E31 means the dryer's contact sensor reads a frequency that is too high, per Electrolux's dryer chart. Empty the drum and look for anything lodged against the sensor. If E31 returns with a clear drum, book a technician.
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
The contact sensor reads how damp the load is. Electrolux’s dryer sheet labels its test row “MOIST. BARS” and ties E31 and E32 to a frequency reading that is too high or too low. A foreign object touching the sensor is one listed cause.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.