What it means
F44 applies to Electrolux's ES630 oven control only and means the cooling fan is running too fast. The display board reads the speed and flags it. Modular ovens print F46 for the same condition. Book a technician.
Electrolux oven F44 / Cooling fan
F44 applies to Electrolux's ES630 oven control only and means the cooling fan is running too fast. The display board reads the speed and flags it. Modular ovens print F46 for the same condition. Book a technician.
Also shown as F44
F44 applies to Electrolux's ES630 oven control only and means the cooling fan is running too fast. The display board reads the speed and flags it. Modular ovens print F46 for the same condition. Book a technician.
Is it unusually loud or fast?
F44 returns or the fan is unusually loud.
Your checklist, kept on this device

Is it unusually loud or fast? The sheet asks whether the fan appears to turn normally by airflow and noise.

Make sure nothing blocks the fan's airflow, which could make it speed up.

Shut off the oven at the breaker, wait 30 seconds, then restore power, then restore it.

A supply more than 10 percent above 120VAC can make the fan too fast, but measuring it is a technician's job.

The sheet checks the fan, its blade and supply, the speed sensor connection, then replaces the fan and sensor assembly and the display board.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The cooling fan keeps the oven’s outer cabinet from overheating.
Read the definitionThe fan speed read at the display board is too high. The sheet puts the trigger above about 2500 RPM.
Read the supporting manualThe sheet lists a loose fan blade, a blocked airflow path, a voltage more than 10 percent above 120VAC and a misconnected speed sensor.
Read the supporting manualThe sheet replaces both the fan and sensor assembly and the display board.
Read the supporting manualF46, cooling fan speed too high. F44 is only on the ES630.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30EW65PS
p/n 807436903 (Rev A 13/04) / PDF p.1 (EOC code descriptions)
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30EW55PS
p/n 807436904 (Rev A 13/04) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30DS80RS
p/n 807880710 EN (Rev A 16/02); 807880711 FR (Rev A 16/03) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EI30EW38TS
p/n A00980644 Rev A (2017/05) / PDF p.2 (F46)
Row F44 of the ES630 sheets (807436903, 807436904, 807880710). The modular sheets print F46 for the same condition.
Not until a technician has checked the fan. The cooling fan protects the electronics, and a fast fan can point to a loose blade or a supply problem.
No. F43 is a cooling fan that is too slow. F44 is one that is too fast. They share a test mode that shows fan speed in RPM.
The sheet says a voltage higher than 120VAC plus 10 percent could make it go too fast.
For F44, the model number, any change in fan noise and whether the fan is blowing air out of the vent above the upper door.
Codes, symptoms, parts and service
F43 applies to Electrolux's ES630 oven control only and means the cooling fan is turning too slowly. The display board reads the fan's speed and finds it abnormal. Modular ovens print F45 for the same condition. Book a technician.
The written Electrolux articles say little about setting the clock or timer, since its display-settings guide is a video. What they do cover is a display or keypad that acts up: a stuck key (F11), memory and cable errors (F13, F14, F15), Demo mode and a power reset.
The cooling fan keeps the oven’s outer cabinet from overheating. The ES630 sheet reads its speed through a tachometer: F43 means too slow and F44 too fast. The 2017 modular sheet uses F45 for too low and F46 for too high.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.