Start from the symptom
Electrolux oven fan problems.
The ES630 sheets show a cooling fan and a convection fan. The sheets watch the cooling fan's speed: F43 and F44 on ES630 ovens, F45 and F46 on modular ovens. An even-cooking complaint, by contrast, may be about how food is arranged.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Run a bake and feel the air
The ES630 sheet suggests starting a bake and checking within the first 15 seconds whether the fan turns, which you can feel as air flowing through the vents above the upper oven door.
- 2
Know which code you have
F43 is a cooling fan running too slowly and F44 too fast, both on ES630 ovens only. Modular ovens print F45 for too slow and F46 for too fast.
- 3
Keep the air flowing
For F44 the sheet says to verify nothing is blocking the airflow of the fan. Keep the vents above the door clear.
- 4
A fan that may be normal
On an ES630 the cooling fan runs at low speed during any cooking function and stays on until the oven has cooled down. High speed is used only during broil with the door open and during clean cycles above roughly 575 degrees F, so a change in fan sound is not always a problem.
- 5
Even browning is about airflow
Electrolux's even-cooking article says to spread food out in one layer so air can reach each piece.
- 6
Power reset
Disconnect the oven for 30 seconds and restore power. Electrolux says this clears most false codes. If the code returns, the fan or its speed sensor needs a technician.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.
If the display adds a code.
Cooling fan
F43 applies to Electrolux's ES630 oven control only and means the cooling fan is turning too slowly. The display board reads the fan's speed and finds it abnormal. Modular ovens print F45 for the same condition. Book a technician.
Cooling fan
F44 applies to Electrolux's ES630 oven control only and means the cooling fan is running too fast. The display board reads the speed and flags it. Modular ovens print F46 for the same condition. Book a technician.
Cooling fan
F45 means the cooling fan speed is too low on Electrolux's modular wall oven control. The ES630 prints F43 for the same condition. Check the fan blades are not blocked, then book a technician.
Cooling fan
F46 means the cooling fan speed is too high on Electrolux's modular wall oven control. The ES630 prints F44 for the same condition. Check for an obstruction in the air path, then book a technician.
Read the related care guide.

F14 or F15 on the oven? Check which control you have.
F14 appears only on the ES630 oven control and means a misconnected keyboard cable. F15 means a failed controller self check on the ES630 but a keyboard error on the 2017 modular control, so your model number decides which row applies. Switch the oven off for 30 seconds, then book a technician if it comes back.

Oven keys or display acting up? Start with lock, demo and a reset.
The Owner Center explains Electrolux oven clock and display settings in video articles with no written steps, so use your Use & Care guide for those. In writing, it covers locked controls, demo mode and a 30-second power reset, and the oven sheets cover keypad codes F11, F13, F14 and F15.
When observation becomes a service request.
Leave internal testing to a technician.
Book a technician if the fan seems not to turn, F43, F44, F45 or F46 returns after a reset. Tell us the code, and whether you have an ES630 or modular control.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux oven fan problems guidance. Use the manual for your own model.
- Service Data Sheet, p/n 807436903, "Appliance with ES630 Electronic Oven Control" (EW30EW65PS)
- Service Data Sheet, p/n A00980644, "Electric wall ovens with modular oven controls" (EI30EW38TS)
- Ovens - Why isn’t my food cooked evenly? (KB 1847391)
Follow the guide for your exact model. Consult how we research these pages.
What do F43 and F44 mean?
On ES630 ovens, F43 means the cooling fan is turning too slowly and F44 too fast, measured by the display board. Modular ovens print F45 and F46 instead.
How can I check whether the cooling fan runs?
Start a bake and, in the first 15 seconds, feel for air coming through the vents above the upper oven door. This check comes from the ES630 sheet.
Is it normal for the fan to keep running after baking?
Yes. The ES630 sheet says the cooling fan starts at low speed with any cooking function and stays on until the oven has cooled. High speed is limited to open-door broil and clean cycles above about 575 degrees F.
What helps food cook evenly?
Air has to move around each piece, Electrolux says. Spread food in one layer instead of stacking or crowding it.
Codes, symptoms, parts and service
Link the message to what to do next.
F43
F43 applies to Electrolux's ES630 oven control only and means the cooling fan is turning too slowly. The display board reads the fan's speed and finds it abnormal. Modular ovens print F45 for the same condition. Book a technician.
Electrolux oven clock, timer or display problems
The written Electrolux articles say little about setting the clock or timer, since its display-settings guide is a video. What they do cover is a display or keypad that acts up: a stuck key (F11), memory and cable errors (F13, F14, F15), Demo mode and a power reset.
Oven cooling fan
The cooling fan keeps the oven’s outer cabinet from overheating. The ES630 sheet reads its speed through a tachometer: F43 means too slow and F44 too fast. The 2017 modular sheet uses F45 for too low and F46 for too high.
Oven repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
